Bitumen Heating

August 2, 2013

WHY IS IT WORTHWHILE TO HEAT BITUMEN ELECTRICALLY?

INTRODUCTION 

In today’s oil industry, there a fewer and fewer new finds of light crude petroleum. New sources, whether they be from the Canada tar sands, from shale oil or from offshore drilling for example, are often heavy oil, bitumen and asphalt. The two latter terms, sometimes used interchangeably, refer to long hydrocarbon chain molecules of very high viscosity.
 
 

 














Figure 1 – Bitumen flow by gravity is very sluggish in cold weather
 
 
Because of the growing importance of heavy oil, bitumen and asphalt, new techniques must be applied to process them. A basic challenge is to make them flow: from the reservoir to the refinery; from one station of the refinery to the next; from a depot tank to a truck or a railway car, among other situations.

 
 

Figure 2 - Effect of temperature on the viscosity of gas-free Athabasca (ARC) bitumen at constant pressure [1]
 
The extremely high viscosity shown for Athabasca bitumen in Figure 2 is typical of all bitumen - for reference, the viscosity of water is 8.9 x 10-4 Pa-s. Also typical is the observed tendency of the viscosity to decrease exponentially with temperature.
 
In this article, we demonstrate quantitatively the importance of heating heavy oil products before pumping. For convenience, we will simply use the term bitumen to designate all the heavy oil products described above.
 
 

 
 

DEPENDENCE OF PUMPING POWER ON TEMPERATURE

 
The power P required to pump bitumen at a flow rate Q across a pipe in which the pressure drop is Δp is given by:
                                                                             (1)
The pressure drop in turn, is proportional to the friction factor f, the ratio of pipe length l to diameter d, and the dynamic pressure ρV2/2, where ρ is the density and V the velocity:
                                                                (2)
As bitumen is extremely viscous, the flow is laminar and we have the familiar expression for the friction factor, f = 64/Re where Re is the Reynolds number
                                                                          (3)
The flow rate Q is related to the pipe diameter d and velocity V by
                                                                                    (4)
 
Substituting from equations 2, 3 and 4 into 1, we obtain for the power the expression
                                                            (5)
In equation (5), we see that the pumping power is directly proportional to the temperature-dependent viscosity. A calculation with equation (5) and the viscosity data of Figure 2 illustrates the impact of heating, Table 1.

 
 
 
Effect of Temperature on Pumping Power of Bitumen
 
CONDITIONS
Volume flow rate: 250 barrel/hour
Pipe diameter: 3 in
Pipe length: 500 ft
Bitumen density 63.05 lb/ft3
Velocity 7.94 ft/s
CALCULATED PUMPING POWER VS. TEMPERATURE
TEMPERATURE VISCOSITY, PA-S PUMPING POWER, kW
oC oF    
40 104 17 382.0
60 140 2.8 62.9
80 176 0.6 13.5
100 212 0.2 4.5
 
Table 1 – Huge savings in pumping power are obtained by heating bitumen
 
Pumping power essentially decreases twenty-five-fold, from 382 kW to 13.5 kW, by heating the bitumen from 40 oC to 80 oC.
It should be pointed out that there is a savings not only in pumping power, but in capital cost, as a 13.5 kW pump costs but a small fraction of a 382 kW pump.
 

 
TECHNIQUES FOR ELECTRICAL HEATING OF BITUMEN

 

Figure 3 – Cross-section of a bitumen tank with electrical pipe heater.
 
Several techniques are used to heat bitumen. Electrical heating is a prime choice because of its precision, uniformity and compactness, among other qualities. Common arrangements are:
·         An immersion-type tank flange heater, comprising several metal-sheathed resistance heating elements in direct contact with the bitumen. The bitumen is heated and circulates by natural convection inside the tank;
·         A circulation heater. Here the flange heater is inside a circulation vessel fitted with inlet and outlet connections; heat transfer to the bitumen occurs by forced convection;
·         A pipe heater, one in which the heating elements are enclosed in a pipe and thereby shielded from direct contact with the bitumen as seen in Figure 3. This arrangement may be preferred in case of extreme viscosity.
In general, all bitumen must be considered as a flammable liquid or presenting the danger of an explosion in case of excessive heating. The maximum storage and handling temperature corresponds to the flash point, i. e. the temperature at which the vapor above which a liquid will catch fire in the presence of air and of a source of flame. This temperature varies according to the quality; a typical value is 450 oF. Accordingly, it is recommended that bitumen heaters have an explosion-proof (NEMA 7) enclosure.
 
NOMENCLATURE
 
NAME SYMBOL ENGLISH UNIT SI UNIT
Density ρ lb/ft3 kg/m3
Friction factor f (dimensionless)
Pipe diameter d in m
Pipe length l ft m
Power P HP kW
Pressure drop Δp psi kPa
Reynolds number Re (dimensionless)
Velocity V Q ft/s m/s
Volume flow rate   barrels/hour m3/s
 
 
 

REFERENCES
 
[1]Mehrotra, A. K. and W. Y., C. J. Ch. E., v. 64, Oct. 1986.

Latest blogs

Unique considerations when choosing an immersion heater 2

  • News
  • Apr 18 2017

It is important to choose the right immersion heater for your specific application to get the most efficiency and longest lifespan. Selecting the right industrial heating equipment reduces cost, imp...

Read more..

Heating equipment brewing industry

  • News
  • Mar 7 2017

Introduction to heating equipment in the beer brewing industry   The beer brewing process is complex and requires fine attention to detail to have great-tasting beer come out as a resul...

Read more..

Select right industrial heating element

  • News
  • Feb 8 2017

Industrial heating elements are among the most crucial components in any industrial heating system. Selecting the right industrial heating element can save money, time, and create a more efficient pro...

Read more..

Wattco inline water heaters in depth

  • News
  • Dec 19 2016

Overview of Inline HeatersOverview of Inline Heaters Wattco inline heaters are designed to enhance the performance of a regular immersion heater, heating up liquid solutions while maximizing efficien...

Read more..

Wattcos in depth guide to circulation heaters

  • News
  • Nov 30 2016

Circulation heaters, sometimes called In Line Heaters, are compact heating units used in a variety of ways across industry. Common applications for circulation heaters include heating liquids and gase...

Read more..

Wattco immersion heaters in the food industry

  • News
  • Nov 17 2016

The food manufacturing industry requires dependable, efficient industrial heating equipment to create the high-quality products consumers expect. Wattco industrial immersion heaters are a perfect fit ...

Read more..

Wattco control panels in depth

  • News
  • Nov 1 2016

Wattco control panels are designed to maintain reliable and efficient heat transfer in a heating system and to keep an industrial process running at full operational capacity. Wattco control panels an...

Read more..

Wattco duct heaters in depth

  • News
  • Oct 27 2016

Wattco has earned its reputation for providing high-quality duct heaters over years of long-standing service to a range of industries. Common industries we work with include chemical, manufacturing, o...

Read more..

Industrial heaters in the pulp and paper industry

  • News
  • Oct 20 2016

Industrial Heaters, or Process Heaters, as they are commonly referred to, are used to make a wide variety of processes more efficient across a large range of industries including the water purificatio...

Read more..

Common Industries that Wattco works with

Case Studies View All

5 Fundamental Rules for Designing Efficient Heat Transfers
Considering these basic rules for designing thermal heat transfers will expand a project’s ..
Read more..

Advantages and Limitations of Digital Control Panels for Industries
Digital control panels are widely used in industries to monitor and control system variables. Hum..
Read more..

Air Duct Heaters
Air duct heaters are commonly used in the HVAC industry. They provide supplementary heat to the d..
Read more..

Alternatives to Direct Immersion Heaters
  Although immersion heaters are most often the best possible solution for tank content ..
Read more..

Bitumen Heating Texan Style
Bitumen Heating In places like Houston Texas, bitumen is well known in the construction indus..
Read more..

Wattco News View All

Articles : IMMERSION HEATING ELEMENTS
Several examples of heating elements and their uses can be found here. Immersion heaters are found in many applications in oil and gas exploration....
Read more..

Band Heater
Band heaters are clasps that hug around the pipe so that the fluid inside gets warm....
Read more..

Heating Bitumen
The construction industry uses bitumen and runs into problems transporting it from one container to the other. This is an article that explains why bi...
Read more..

Bitumen Heating
Bitumen heating using electric heating elements and controls...
Read more..

Boiler Water Heaters
A boiler water heater can be used to heat up water to practically any temperature. They are also constructed to resist high pressure....
Read more..

Most Popular Blogs